Clopay Cable & Drum Replacement Nationwide

Clopay Cable & Drum Replacement: The Pembroke Pines Owner’s Guide

Clopay cable and drum replacement in Pembroke Pines typically runs $130 to $250 installed for the pair, and we carry compatible Clopay-spec parts on our trucks for same-day service in most cases. You’ll usually know this part failed because the door hangs crooked in the opening, or you’ll hear a sharp pop followed by the door refusing to lift evenly. The cable and drum work together as the winding mechanism that transfers spring tension into lifting force, so when one side fails, the door goes sideways fast, sometimes literally.

Call (954) 280-1425

Which Clopay Models This Applies To

We replace cables and drums across the Clopay lineup, including the Classic, Gallery, Coachman, Canyon Ridge, and Reserve series, plus the IntelliCore and steel-back models that came through a lot of Pembroke Pines builds between 2015 and 2025. The compatibility gotcha with Clopay doors is that the drum is matched to the spring wire diameter and the cable length is matched to the door height, not the door brand. A 7-foot door takes a different cable than an 8-foot one, and a drum from a 0.250-inch spring system will not seat correctly on a 0.225-inch spring setup, even on the same Clopay door series.

If you’re trying to identify what you have, the manufacturer label on the left door jamb is the fastest route. It lists the model and series. If that label is gone, the end bearing plate and drum profile tell us the rest. On the OEM versus aftermarket question for Clopay specifically, we stock both. The factory Clopay cables are pre-stretched and cut to the exact model spec. For some older Clopay doors, a precision aftermarket equivalent from a supplier we’ve used for years runs within tolerance and saves you $30 to $50 on the cable itself. We’ll show you the difference on the truck before we touch anything.

Signs Your Clopay Cable & Drum Replacement Is Failing

• Crooked door in the opening: One cable stretched or slipped off the drum, so one side lifts while the other stalls. This is the most common symptom we see along the Pines Boulevard corridor.
• Loose or tangled cable around the drum: A broken cable or a drum that lost its set screw lets the cable unwind off the drum. Never grab a loose cable while the door is under tension, and don’t try to re-seat it yourself.
• Grinding or scraping when the door moves: A worn drum with a rolled bearing or a frayed cable dragging through the pulley creates a sound that doesn’t belong in a smooth Clopay door.
• Visible fraying or separated strands on the cable: Galvanized aircraft cable dries and corrodes in Florida humidity. Once you see individual strands broken, the cable is at maybe 15 percent of its original strength.
• Door stops mid-lift and binds: The cable jumped the drum and is now jamming between the drum and the end bearing plate. Continuing to cycle the door with the opener will carve a groove into the drum and may bend the shaft.

Before

After

Replacement Cost & What’s Included

Cable and drum replacement on a Clopay door in Pembroke Pines lands between $130 and $250 installed, depending on the series, the drum type, and whether the springs need re-tensioning at the same time. The labor is the larger share of that number because we re-set both cables, set the drums to the correct track, and re-balance the door before we call it done. Parts themselves usually run $40 to $80 for a matched cable and drum set.

Every quote is a flat, written price with a written scope of work before any wrench comes out. That’s Clause 1 of The Haven Standard, and it means the price you approve is the price you pay, no add-ons when you’re already committed. The work carries our 365-Day Done Right Promise in writing.

Key Takeaways

• Clopay cable and drum replacement in Pembroke Pines: $130 to $250 installed.
• The drum must match the spring wire diameter; the cable must match the door height. We verify both before quoting.
• We stock Clopay-compatible cables and drums on the truck. Same-day replacement is realistic in most cases.
• You receive a written price and scope before work starts, and a documented photo record of what was found and what we did when we leave.

DIY or Call Us?

Cables and drums work under spring tension. Even with the door fully open, the lifting cables on a standard torsion system carry load. If you have a frayed cable or a drum that’s come loose, the safe move is to stop cycling the door and call us. The parts on a Clopay door sit next to the torsion springs, and a cable snap releases stored energy. That’s not a scraped knuckle risk; that’s a hospital visit risk. We’re not being dramatic. We’ve seen what a flying cable end does to a finished wall and to a hand.

What you can safely do is note which side failed, take a photo of the cable condition and the drum area with the door closed, and have that ready when you call. That photo helps us confirm the series and bring the right drum on the first trip. Marcus Deller grew up in the trade and learned early that a homeowner who sees the failed part makes a better decision than one who doesn’t. Name the part, quote the range, then fix it – in that order.

FAQs